You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 75 Next »

Attention:

Please note that operations of the Multibeam Echo Sounder EM710 requires experienced scientific staff on board and can be only operated upon request. The system is not operated by the ship's crew. Request operations with the Multibeam Echo Sounder EM710 toAWI-Logistics in sufficient time prior to the cruise and clarify the data transfer after the cruise.

Summary

Multibeam EM710 is a high-resolution seafloor mapping system. It is suitable for water depths up to 2000m depending on the configuration of the transducers. Maximum ping rate is 30Hz and maximum fan width 140° and depth resolution 1cm. Data from the water column may also be stored.

Manufacturer Kongsberg
Model EM710
Serial No. n/a
Type echo sounder

Transducer Frequency

40 - 100 kHz

Contacts

Name Institution Role
FIELAX GmbH Engineer In Charge

Components

The EM710 consists of a transducer array for transmitting (Tx) and an array for receiving (Rx), the transceiver unit, the data aquisition PC with the aquisition software SIS and two processing PCs (bridge and Messraum) with the software Caris HIPS/SIPS.

The software "Seafloor Information System" (SIS) contains several graphic displays for quality checks and for system calibration as well as other tools. SIS supports an online/realtime data cleansing. Both SIS and the processing software Caris HIPS/SIPS  are protected via a dongle. Please contact the bridge staff for suppport.

Subdevices

Name Model Type
multibeam EM710 Rx multi-beam echosounder
multibeam EM710 Tx multi-beam echosounder

Position

Origin Description:The system consists of several units. Transducer arrays are installed in the keel of RV Heincke. Electronics are found in the Lotgeraeteraum. Work places are situated on the bridge and in the Messraum.

Data logging, storage and archiving

Logged parameters

Parameter Sensor Output Type Unit
depth depth m

Central geographical ship's position and time standard

The GPS position of the Trimble GPS receiver antenna is stored in the data files. The position is NOT centralized to the SES2000 transducers. Heave correction between the motion sensor and the transducer are calculated in the motion sensor and corrected values are transferred to the SES2000. Time synchronisation is achieved via NTP. Centralization of the GPS position to the transducer is achieved by  SIS software. GPS antenna position and transducer position related to the motion sensor position as a reference point are stored in the data files. Pay attention that in case of failure of the Trimble GPS sensor the Saab GPS sensor may be used as the reference GPS source. Please contact the bridge staff for information about the GPS receiver in use. Heave correction values are only available for the Trimble GPS receiver. Heave correction between the motion sensor and the transducer is calculated in the EM710 transceiver unit. UTC time synchronisation of the transceiver unit is achieved via GPS with PPS. The PC is synchronised with UTC via the Windows-Domain-Affiliation to ensure a correct naming of the dat  files.

Rawdata storage on board

The data acquisition software SIS creates raw data on the local drive of the computer. The EM710 data are not transferred to DSHIP.

root directory E:\sisdata\raw\ or \\xdc\home\data\mbes\
directory nameCruiseNo e.g. HE507
file namennnn_YYYYMMDD_hhmmss_Suffix.all 
Data volume (MB per day) ca.2800
Number of files per day ca.50

Dship

The EM710 outputs water depths of the central beam via a serial connector to DSHIP.

Device nameMultibeam Echosounder
ParameterDepth [m]

Data archiving on land

After consultation with the data scientist and AWI Logistics the EM710 data including meta data may be transferred to PANGAEA  (https://www.pangaea.de/).

Documentation

  • No labels